HOBBYSKY DS-600 6-ch Ship Model Remote Control 2.4G RC Pull net to Play Fishing Boat / RC Car / RC Copter Heli With Fixed Speed Remote Control

Product Description:

Pairing steps:

• Turn off the transmitter and receiver first:
• Insert the encoder into the "B" port of the receiver.
• Connect the power cable to the corresponding channel interface of the receiver (the receiver light is flashing rapidly at this time)
• Turn on the power switch of the receiver (the receiver light is always on at this time)
• Unplug the code pairer, the code pairing is successful.

Receiver LED light status:

• Blinking: Indicates power is on, no signal, no match
• Steady on: Indicates that the matching code is successful.

Charging Instructions:

• Built-in remote control: 1200mAh lithium battery, charging IC has protection function, battery built-in protection function, dual design.
• Please choose the adapter: 5V

Charging method:

• A. The remote controller needs to be turned off during the charging process.
• B. The red light is charging, the green light is fully charged.

Description of mixing function settings:

• 1. Function description
  Mixing mode allows 1-ch and 2-ch to control 2 motors at the same time for throttle forward and reverse or differential steering.
• 2. Setting method
  A. The remote control is turned off first.
  B. Press and hold the (3-sh) switch first, then turn on the power switch of the remote control, the mixing indicator (green light) on the remote control panel will be on.
  C. The operation method of opening and closing the mixing control is the same, and the indicator light of the mixing control closing state will be off.

Out-of-control protection function setting instructions:

• 1. Function description
  The out-of-control protection function is to protect the receiver from losing the signal to avoid losses due to out-of-control.
  It is mainly set by the throttle channel. When the receiver cannot receive the control signal, the throttle of the receiver will be set.
  The channel will run to the originally set value to avoid misoperation, and the factory default value of the fail-control protection is the neutral point.
• 2. Setting method
  a. Before setting the out-of-control protection, you need to match the transmitter and receiver to the code successfully;
  b. Turn on the power-on state of the transmitter and receiver (at this time, the signal light of the receiver is always on);
  c. Control the throttle channel of the transmitter to make the throttle control servo or governor enter the braking or flameout state
  state, and then remain motionless;
  d. Insert the encoder into the "B" port of the receiver (the receiver LED will flash at this time)
  And after 3 seconds, the light is always on, and the fail-safe protection setting is completed.
• 3. Functional testing
  a. Turn off the transmitter power,
  b. Check whether the servo of the throttle channel enters the set state.

Notice:

• It is recommended to set the safe return position of the throttle servo to the brake or neutral point, do not set it to open the throttle
  position to avoid danger. The system's factory default out-of-control protection functions are as follows:
• Tram - the steering servo is at the neutral point, and the speed controller throttle is at the static neutral point.
• Oil truck - the position of the steering servo is at the neutral point, and the throttle servo is at the idle position

1-ch/2-ch forward and reverse channel setting instructions method:

• A. The remote control is turned off first;
• B. Press and hold the [4 channel] switch first, then turn on the power switch of the remote control;
  At this time, you will hear a "beep", and the remote control enters the setting state.
• C. Note that only the forward and reverse directions of one channel can be set at a time,
  Push the first or second joystick to the maximum or minimum, and hear a long beep of "di"
  Prompt, the setting is complete.

Stroke setting instructions:

•  Function description
  The size of the 1.2.3.4.5.6 channel stroke of the remote control can be adjusted;
  Note: Except that there is no action feedback during the 2-channel throttle adjustment process,
  1.3.4.5.6 The channel will have action feedback during the adjustment process to facilitate observation
  the state of adjustment.
• 2. Setting method
  a. The remote control is turned off first;
  b. Press and hold the [OK speed key], then turn on the remote control power switch;
  (At this time, the two lights of the remote control (red light and blue light) will flash at the same time).
  c.【ST.TRIM】button plus or minus to set the size adjustment of the direction stroke amount of 【1 channel】;
  (The factory default stroke has been appropriately reduced, and the maximum stroke to the minimum stroke is divided into 20 gears)
  【TH.TRIM】button plus or minus to set 【2 channel】the size adjustment of throttle stroke;
  (The factory default stroke is the maximum, the maximum stroke to the minimum stroke is divided into 5 gears)
  [3.4.5.6] There are 10 gears from the maximum stroke to the minimum stroke of the channel, which are cyclically adjusted;
  (The factory default stroke amount is the maximum, and the corresponding channel stroke amount can be adjusted by the remote marked channel button)

Note: The antenna of the receiver is mainly used to receive signals. Please do not pull the antenna during use.
In the case of cutting, etc., the received signal will be stronger when the receiver antenna is upright.

Receiver Function Setting Instructions:

• 1. Model description
  This remote control has a variety of models of receivers to choose from, and supports customization.
  1: [6-ch receiver] 2: [4+2 receiver] 3: Power integrated receiver with brushed version
• 2. Function description
  a. : (6-ch) Each of the 6 chs is a PWM signal.
  b. : (4+2 receivers) 1-ch PWM signal, 2-ch throttle PWM signal,
  3-ch and 5-ch can only select one channel to use at the same time, 3-ch is the PWM servo signal,
  5-ch is the power signal, which is mainly used to control lights or trawl hooks, etc.;
  4-ch channel and channel can only select one channel to use at the same time, the channel is PWM servo signal
  6-ch is the power signal, which is mainly used to control lights or trawl hooks, etc.
  C.【Power integrated receiver with brushed version】: This receiver integrates the receiver and power controller with
  Integrated, the receiver can be customized according to customer needs.

 

 

Standard  Shipping:
Order now and we will ship your skateboard by sea / by train / by truck
US / Canada  Arrivals 35-50 Business Days (After shipping)
UK Arrivals 40-55 Business Days (After shipping)
European Arrivals 60-70 Business Days (After shipping)
  
Air Shipping: 
Order now and we will ship your skateboard by air
US / Arrivals 7-15 Business Days (After shipping)
Europe, Canada / Arrivals 15-20 Business Days (After shipping)
Asian countries / Arrives 7-15 Bussiness Days (After shipping)

Q:What's the current shipping time?
(From the shipping date provided by the logistics company)

Standard Shipping from Factory: Shipped by Sea, Train or Truck

Fast Shipping from Factory: Shipped by Air
United States: 7-15 Business Days (Fast Shipping)
United States: 35-50 business days (Standard Shipping).
Europe: 15-20 business days (Fast Shipping)
Europe: 60-70 business days (Standard Shipping by sea)
Europe: 30-35 business days (Standard Shipping by truck)
Canada: 15-20 business days (Fast shipping)
Canada：35-50 business days (Standard Shipping)
United Kingdom: 25-30 business days (Standard Shipping by truck)
Australia: 15-20 business days (Fast Shipping)
South Korea: 5-7 Business Days (Fast Shipping)
Japan: 12-15 business days (Fast Shipping)
Taiwan: 7-15 business days (Fast Shipping)
Singapore: 7-15 business days (Fast Shipping)
West Malaysia: 12-20 business days (Fast Shipping)
East Malaysia: 12-20 business days (Fast Shipping)
Vietnam: 12-20 business days (Fast Shipping)
Shipping from US Warehouse （US ONLY): Arrives 2-7 Days (After Shipping)

If you have any question please Email us!